Zurich 56218 Owner'S Manual Download Page 29

Page: 29 / 101

Live Data Mode

LIVE DATA PLAYBACK

For technical questions, please call 1-888-866-5797.

With the Scan Tool not connected to a vehicle, press

POWER/LINK

The "To Link" screen displays.

Press and hold

until the Live Data Menu displays.

Select

Playback Live Data

, then press

ENTER

The Playback Live Data menu displays.

When you select

Yes

from the Record Live Data confirmation

screen, the Scan Tool enters the "Live Data Playback" mode,

and the Playback Live Data menu displays.

Select

Continuous Playback

Frame by Frame

, as desired, then

press

ENTER

The display shows the recorded Live

Data, beginning with the "trigger"

frame.

Only  a  limited  amount  of  PID  data
can  be  displayed  on  the  screen  at
one  time.  If  additional  PID  data  is
available, a small arrow is shown on
the  display.  Press

and

DOWN

, as necessary, to view

all available PID data.

When viewing recorded Live Data, look for any irregularities in any of

the PID values/signal information (LTFT %, RPM, MAP, TEMP, etc.).

If any PIDs are not within specification, or irregularities are detected,

follow the procedures in the vehicle's service repair manual to

perform additional troubleshooting and repair.

When you select

Continuous Playback

, the Scan Tool plays

recorded data at a rate of one frame / 15 seconds. When playback is

finished, a Playback Complete message displays.

To play the data back again, select

Continuous Playback

Frame by Frame

, as desired, then press

ENTER

To exit Live Data Playback mode, choose

Exit

When

Frame by Frame

is selected, you must scroll the individual

frames manually.

When you have viewed all PID information for the current frame of
Live Data, choose

Next Frame

Previous Frame

, as desired.

To exit Live Data Playback mode, select

Exit Playback

, then

press

ENTER

If there is no Live Data currently stored in the Scan Tool's memory,
an advisory message shows on the display. Choose

Main Menu

to return to the Main Menu.

Summary of Contents for 56218






































































































Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands

Zurich 56218, Owner'S Manual

Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands