Zurich 56218 Owner'S Manual Download Page 77

Page: 77 / 101

Additional Tests

SYSTEM/ACTUATOR TESTS

For technical questions, please call 1-888-866-5797.

An “instructional” screen displays. Prepare the vehicle for test as

directed:

- Make sure fuel level is less than 9/10.

- Make sure fuel temperature is below 35°C.

- Turn the ignition on. DO NOT start the engine.

- Place the transmission in PARK.

Choose

Continue

to proceed.

The vehicle’s computer performs a

9-step check of the EVAP system. A

“status” screen displays the name

and number of the current

Step

, the

Vapor Pressure

, and the status of

the

Purge VSV

Vent Valve

and

Vacuum Pump

Choose

Next Step

as needed to scroll to

the next stage of the test.

When the test is completed, a

“confirmation” screen displays.

Choose

Exit

to return to the PCM

Actuator Test and Special Function

Menu.

Summary of Contents for 56218






































































































Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands

Zurich 56218, Owner'S Manual

Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands