Zurich 56218 Owner'S Manual Download Page 54

Page: 54 / 101

Additional Tests

SYSTEM/ACTUATOR TESTS

For technical questions, please call 1-888-866-5797.

Engine Speed Control

Throttle Position

Throttle Sweep

Reset Idle Learn

EGR Solenoid

Fuel Injector Balance

Cylinder Power Balance

Misfire Graphic

Engine Oil Life Reset

Crankshaft Position Variation Learn

HO2S Learn Sensor

If an error occurs while performing any function, an “advisory”

message displays. Choose

Exit

to return to the ECM Special

Functions menu.

Engine Speed Control

The Engine Speed Control function lets you increase or decrease engine

speed from a base commanded RPM in 25 RPM increments.

Select

Engine Speed Control

in the ECM Special Functions menu,

then press

ENTER

An “instructional” screen displays. Prepare the vehicle for test as

directed:

- Set the parking brake.

- Block all drive wheels.

- Start and idle the engine.

Choose

Next

to continue.

Engine speed is commanded to 550

RPM and the RPM Control test

screen displays.

The screen shows the

Commanded

RPM

actual

Engine Speed

, and the

Desired Idle Speed

Choose

Decrease 25 RPM

Increase

25 RPM

, as desired, to decrease or

increase engine speed, and observe

results on the display.

To exit the test, press

ENTER

to reduce the commanded engine

speed to 0 RPM, then press

ENTER

again to return to the ECM

Special Functions menu.

Summary of Contents for 56218






































































































Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands

Zurich 56218, Owner'S Manual

Search results

Summary of Contents for 56218

Reviews:

Related manuals for 56218

Brands by name

Popular brands