YSI 5200A User Manual Download Page 4

Page: 4 / 139

YSI 5200A
6

YSI 5200A
7

Table of Contents

Control Mode ............................................................................149

Set Point Control ................................................................150
Timed versus Normal (non timed) Control ..........................153

Validation Error and Autofix - Set Point Control Only

.........154

PID/PWM and PID 4/20mA Control mode ..........................155

Aux and E-Aux Relay Digital ....................................................161
Aux and E-Aux Analog (0-1VDC, 0-5VDC and 4/20mA) ..........163
Temperature .............................................................................165
Conductivity ..............................................................................168

Temperature Compensation ...............................................168

Configure Conductivity System

..........................................169

DO ............................................................................................170

Salinity & Temperature Compensation for DO Readings ...170
Two Range Controls for DO ...............................................171

Configure DO Sensor System

............................................171

ORP..........................................................................................173

Configure ORP sensor system

...........................................173

pH .............................................................................................174

Configure pH system

..........................................................174

Salinity ......................................................................................175

Enable Salinity System .......................................................176

E-Aux system Offline

..........................................................177

Configure sensor system as a 4/20mA output

....................178

AquaManager and the Sensor Setup Menu .............................179

Timers ............................................................................................180

Timers 1-4 ................................................................................181
Feed Smart

Timer...................................................................182

AquaManager and the Timer Menu ..........................................190

Control Menu .................................................................................192
Msg’s Menu ....................................................................................193

Calibration Logs ......................................................................194
Event Logs ...............................................................................194
Sensor Logs .............................................................................195

Svr Hold Menu ...............................................................................195

5 AquaManager

......................................................... 197

Installing AquaManager .......................................................................198

PC Requirements and Features ....................................................198
Software Installation .......................................................................199

Table of Contents

Getting started ..........................................................................199

AquaManager Windows .................................................................200

Explorer Window ......................................................................200
Node (Graph) Window .............................................................201

Systems Management ........................................................202

Database Management ..................................................................203
Autopoller .......................................................................................204

Mapping ...................................................................................205
AquaManager Alarm Emails .....................................................205

6 Maintenance

...........................................................

207

Maintenance ........................................................................................208

Probe Maintenance at the Deployment Site ..................................208
Algae and Debris ...........................................................................208

Minimizing the Effect of Algae and Debris ................................208

Calibration Checks .........................................................................208
Recommended Quality Assurance Protocol ..................................209

Alternative Quality Assurance Protocol (quick check and adjustment)
211

Sensor Care and Maintenance ......................................................211

DO Sensor ...............................................................................211

Silver Anode Cleaning ........................................................212
Gold Cathode Cleaning ......................................................212

pH and Combination pH/ORP Sensor Cleaning.......................213
Temperature/Conductivity Sensor Cleaning .............................214

Recommended Cleaning of the 5200A and Accessories ...............215
Storage ..........................................................................................215

Short Term Storage ..................................................................215
Long Term Storage ...................................................................215

Probe/Cable Assembly Storage .........................................216
Sensor Storage ..................................................................216

Sensor Replacement .....................................................................217
Charging DC batteries ...................................................................217
AquaManager Database Maintenance ..........................................217
Replacement Parts & Accessories .................................................217

Appendices

............................................................... 219

Appendix 1 - Unpacking and Inspection ..............................................220
Appendix 2 - Troubleshooting ..............................................................221

Sensor Troubleshooting ...........................................................221
Relay (Outputs) Troubleshooting .............................................222
Email Alarm Troubleshooting ...................................................223
Network Troubleshooting .........................................................224
5200A Systems Troubleshooting ..............................................224
Firmware Updater Troubleshooting ..........................................225

Summary of Contents for 5200A












































































































































Search results

Summary of Contents for 5200A

Reviews:

Related manuals for 5200A

Brands by name

Popular brands

YSI 5200A, User Manual

Search results

Summary of Contents for 5200A

Reviews:

Related manuals for 5200A

Brands by name

Popular brands