YSI 5200A User Manual Download Page 128 | Manualshive

Page: 128 / 139

background image

YSI 5200A
255

YSI 5200A
254

Declaration of Conformity

Supplementary
Information:

All performance met the continuous
unmonitored operation criteria as follows:

• ESD, EN61000-4-2:2008 2nd edition

• Radiated Immunity, EN61000-4-

3:2006+A1:2007 3rd edition.

•.EFT, EN61000-4-4:2004 2nd edition, (EFT).

• Surge, EN61000-4-5:2005 2nd edition

• Conducted Immunity, EN61000-4-6:2008 3rd edition

• Voltage Interrupts, EN61000-4-11:2004 2nd edition

• EN61000-4-8:2001 1st edition Power

frequency magnetic field immunity

Authorized EU
Representative

YSI Hydrodata Ltd
Unit 8, Business Centre West, Avenue 1
Letchworth, Hertfordshire, SG6 2HB UK

Signed: Lisa M. Abel

Date: 24 July 2011

Title: Director of Quality

The undersigned hereby declares on behalf of the named manufacturer under our
sole responsibility that the listed product conforms to the requirements for electrical
equipment under US FCC Part 15 and ICES-003 for unintentional radiators.

Manufacturer:

YSI Incorporated
1725 Brannum Lane
Yellow Springs, OH 45387
USA

Product Name:

5200A

Model Numbers

Instrument/Accessory:

5200A

Conforms to the following:

Standards:

• FCC 47 CFR Part 15-2008, Radio Frequency Devices

• ICES-003:2004, Digital Apparatus

Supplementary
Information:

Tested using ANSI C63.4-2003 and CAN/
CSA-CEI/IEC CISPR 22:02

Signed: Lisa M. Abel

Date: 24 July 2011

Title: Director of Quality

Declaration of Conformity

The undersigned hereby declares on behalf of the named manufacturer under our
sole responsibility that the listed product conforms with the Australian and New
Zealand Electromagnetic Compatibility (EMC) requirements for generic products
to be used in residential, commercial, and light industrial environments.

Manufacturer:

YSI Incorporated
1725 Brannum Lane
Yellow Springs, OH 45387
USA

Product Name:

5200A

Model Numbers

Instrument/Accessory:

5200A

Conforms to the following:

Standards:

• AS/NZS 61000.6.3:2007+A1:2009 Electromagnetic

compatibility (EMC), Part 6-3-Emission

• AS/NZC 61000.3.2:2007+A1:2009 EMC,

Limits for harmonic current emissions

• AS/NZS 61000.3.3:2006, Limitation of

voltage changes, voltage fluctuations and
flicker in public low-voltage supply systems

• AS/NZC 61000.6.1:2006 EMC Part 6-1. Immunity.

Signed: Lisa M. Abel

Date: 24 July 2011

Title: Director of Quality

«
...
126
127
128
129
130
...
»

Summary of Contents for 5200A












































































































































Reviews:

No comments

Related manuals for 5200A

Brand: Aalborg Pages: 128

Brand: Palfinger Pages: 34

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Brand: Fagor Pages: 10

Brand: Fagor Pages: 358

Brand: Fagor Pages: 556

Brand: Fagor Pages: 172

Brand: Fagor Pages: 180

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands