![background image](http://html1.mh-extra.com/html/york/ycul0045/ycul0045_installation-operation-and-maintenance_4223634119.webp)
JOHNSON CONTROLS
119
FORM 150.63-NM6 (1020)
22
BAS/EMS DISCHARGE AIRTEMPERATURE RESET
USING A VOLTAGE OR CURRENT SIGNAL
The Remote Reset Option allows the Control Center of the
unit to reset the discharge air temperature setpoint using a
0 - 10VDC input, or a 4-20mA input connected to
XTBC1 terminals A- and A+. Whenever a reset is called
for, the change may be noted by pressing the Cooling
Setpoints key twice. The new value will be displayed
as “REM SETP = XXX °F.”
If a
0 - 10VDC
signal is supplied, it is applied to terminals
A+ and A-, and
jumper JP1 on the I/O board must be
inserted between pins 2 and 3.
To calculate the reset
discharge air temperature setpoint for values between
0VDC and 10VDC use the following formula:
Setpoint = Local Discharge Air Temp Se °Reset
°
Reset =
(DC voltage signal) x (*Max Reset Value)
10
Example:
Local Discharge Air Temp Setpoint = 45 °F (7.22 °C)
*Max Reset Value = 20 °F (11.11 °C)
Input Signal = 6VDC
(English)
°
Reset =
6VDC x 20 °F
= 12
°F Reset
10
New Setpoint = 45 °F + 12 °F = 57 °F
(Metric)
°
Reset =
6VDC x 11. 11 °C = 6.67 °C Reset
10
New Setpoint = 7.22 °C + 6.67 °C = 13.89 °C
* Max Reset Value is the “Max EMS-PWM Remote Temp. Reset” setpoint
value described in the program ming section under Cooling Setpoints.
Programmable values are from 2 °F to 40 °F (1.11 °C to 11.11
°C).
Note: The suction pressure setpoints can not be reset using a
remote option.
If a
4-20mA signal is supplied,
it is applied to terminals
A+ and A- and
jumper JP1 on the I/O board must be
installed between pin 1 and 2
. To calculate the dis-
charge air temp setpoint for values between 4mA and
20 mA use the following formula:
Setpoint = Local Discharge Air Temp Se °Reset
°Reset = (mA signal - 4) x (*Max Reset Value
)
16
Example:
Local Chilled Liquid Setpoint = 45° (7.22 °C)
*Max Reset Value = 10 °F (5.56 °C)
Input Signal = 12 mA
(English)
°Reset = 8mA x 10 °F = 5 °F Reset
16
Setpoint = 45 °F + 5 °F = 50 °F
(Metric)
°Reset = 8mA x 5.56 °C = 2.78 °C Reset
16
Setpoint = 7.22 °C + 2.78 °C = 10.0 °C
A 240-24 Volt Ratio Transformer (T3) is used to
derive nominal 12 volt output from the 120 volt
supply.
A 240-24 Volt Ration Transformer (T3)
is used to derive nominal 12 output from
the 120 volt supply.
Summary of Contents for YCUL0045
