![background image](http://html1.mh-extra.com/html/york/ycul0045/ycul0045_installation-operation-and-maintenance_4223634073.webp)
JOHNSON CONTROLS
73
FORM 150.63-NM6 (1020)
1
INSTALLATION AND ADJUSTING INSTALLATIONS
TYPE CP MOUNTING
Mountings are shipped completely assembled, ready
to install.
1. Locate mountings under equipment at positions
shown on tags or on VM layout drawings, or as
indicated on packing slip or correspondence.
2. Set mountings on subbase, shimming or grouting
where required to provide flat and level surface at
the same elevation for all mountings (1/4" maximum
difference in elevation can be tolerated). Support
the full underside of the base plate – do not straddle
gaps or small shims.
3. Unless specified, mountings need not be fastened
to floor in any way. If required, bolt mountings to
floor through slots.
4. Set the machine or base on
the mountings. The
weight of the machine will cause the upper hous-
ing of the mount to go down, possibly resting on
the lower housing.
5. If clearance “X” is less than 1/4" on any mounting,
with wrench turn up one complete turn
on
the ad-
justing bolt of each mounting. Repeat this procedure
until 1/4", clearance at “X” is obtained on
one or
more mountings.
6. Take additional turns on all mountings having less
than 1/4" clearance, until all mountings have at least
this clearance.
7. Level the machine by taking additional turns on all
mounts at the low side. Clearance should not exceed
1/2" - greater clearance indicates that mountings
were not all installed at the same elevation, and
shims are required. This completes adjustment.
FIG. 12 –
TYPE CP MOUNTING
LD03837
Summary of Contents for YCUL0045
