FORM 150.67-NM2 (209)
11
JOHNSON CONTROLS
1
Responsibility for Safety
Every care has been taken in the design and
manufacture of the unit to ensure compliance with
the safety requirements listed above. However, the
individual operating or working on any machinery is
primarily responsible for:
• Personal safety, safety of other personnel, and
the machinery.
•
Correct utilization of the machinery in
accordance with the procedures detailed in the
manuals.
ABOUT THIS MANUAL
The following terms are used in this document to alert
the reader to areas of potential hazard.
A
WARNING
is given in this document to identify a
hazard, which could lead to personal injury. Usually
an instruction will be given, together with a brief
explanation and the possible result of ignoring the
instruction.
A
CAUTION
identi
fi
es a hazard which could lead to
damage to the machine, damage to other equipment
and/or environmental pollution. Usually an instruction
will be given, together with a brief explanation and
the possible result of ignoring the instruction.
A
NOTE
is used to highlight additional information,
which may be helpful to you but where there are no
special safety implications.
The contents of this manual include suggested best
working practices and procedures. These are issued
for guidance only, and they do not take precedence
over the above stated individual responsibility and/or
local safety regulations.
This manual and any other document supplied with
the unit are the property of YORK which reserves
all rights. They may not be reproduced, in whole or
in part, without prior written authorization from an
authorized YORK representative.
MISUSE OF EQUIPMENT
Suitability for Application
The unit is intended for cooling water or glycol
solutions and is not suitable for purposes other than
those speci
fi
ed in these instructions. Any use of the
equipment other than its intended use, or operation
of the equipment contrary to the relevant procedures
may result in injury to the operator, or damage to the
equipment.
The unit must not be operated outside the design
parameters speci
fi
ed in this manual.
Structural Support
Structural support of the unit must be provided as
indicated in these instructions. Failure to provide
proper support may result in injury to the operator, or
damage to the equipment and/or building.
Mechanical Strength
The unit is not designed to withstand loads or stresses
from adjacent equipment, pipework or structures.
Additional components must not be mounted on the
unit. Any such extraneous loads may cause structural
failure and may result in injury to the operator, or
damage to the equipment.
General Access
There are a number of areas and features, which
may be a hazard and potentially cause injury when
working on the unit unless suitable safety precautions
are taken. It is important to ensure access to the unit
is restricted to suitably quali
fi
ed persons who are
familiar with the potential hazards and precautions
necessary for safe operation and maintenance of
equipment containing high temperatures, pressures
and voltages.
Summary of Contents for YCAL0019
