9-
3
7
ABS (Anti-lock Brake System)
Self-diagnosis with the ABS ECU
The ABS ECU performs a static check of the entire system when the main switch is turned to “ON”. It
also checks for malfunctions while the vehicle is ridden. Since all malfunctions are recorded after they
are detected, it is possible to check the recorded malfunction data by utilizing the YDT when the ABS
ECU has entered the self-diagnosis mode.
TIP
The ABS performs a self-diagnosis test for a few seconds each time the vehicle first starts off after the
main switch was turned to “ON”. During this test, a “clicking” noise can be heard from under the seat,
and if the brake lever or brake pedal are even slightly applied, a vibration can be felt at the lever and
pedal, but these do not indicate a malfunction.
Special precautions for handling and servicing a vehicle equipped with ABS
NOTICE
ECA17620
Care should be taken not to damage components by subjecting them to shocks or pulling on
them with too much force since the ABS components are precisely adjusted.
• The ABS ECU and hydraulic unit are united assemblies and cannot be disassembled.
• The malfunction history is stored in the memory of the ABS ECU. Delete the DTC when the service is
finished. (This is because the past DTC will be displayed again if another malfunction occurs.)
EAS32895
BASIC INSTRUCTIONS FOR TROUBLESHOOTING
1. Check the DTC of “malfunction” using the YDT.
2. Check and repair the malfunction according to applicable DTC troubleshooting.
3. Turn the main switch from “OFF” to “ON”, and then check the DTC of “malfunction” is not displayed.
TIP
• If another DTC is displayed, repeat steps (1) to (3) until no DTC is displayed.
• Turning the main switch to “OFF” will not erase the malfunction history.
4. Do the final check.
WARNING
EWA17420
• Perform the troubleshooting [A]
→
[B]
→
[C] in order. Be sure to follow the order since a wrong
diagnosis could result if the steps are followed in a different order or omitted.
• Use sufficiently charged regular batteries only.
Summary of Contents for XSR900 2022
