Yamaha RX10K Supplementary Service Manual Download

Page: 360 / 523

8-8

IGNITION SYSTEM

ELEC

HANDLEBAR SWITCH (RIGHT)

Engine stop switch and throttle switch
1. Disconnect:

Handlebar switch (right) coupler

2. Connect:

Pocket tester

3. Inspect:

Engine stop switch continuity
Faulty

Replace the handlebar switch

(right).

Switch position

Continuity

RUN (pulled out)

Yes

OFF (pushed in)

4. Inspect:

Throttle switch continuity
Faulty

Replace the handlebar switch

(right).

Throttle switch

position

Continuity

Throttle lever is
operated.

Yes

Throttle lever is not
operated.

CARBURETOR SWITCH

1. Disconnect:

Carburetor switch lead

2. Connect:

Pocket tester

3. Inspect:

Carburetor switch continuity
Faulty

Replace.

Carburetor switch

position

Continuity

Throttle lever is
operated.

Throttle lever is not
operated.

Yes

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands