manualshive.com logo in svg

Yamaha RX10K, Supplementary Service Manual

Get the most out of your Yamaha RX10K with the comprehensive Owner's Manual available for free download at manualshive.com. This detailed manual provides step-by-step instructions, troubleshooting tips, and valuable insights to enhance your experience with this exceptional product. Don't miss out on this essential manual, download it today!

Share
Download
background image

5-56

CRANKCASE

ENG

NOTE:

NOTE:

15. Select:

S

Big end bearings (P

1

 

X

 P

4

)

S

The numbers 

A

 stamped into the crankshaft

web and the numbers 

1

 on the connecting

rods are used to determine the replacement
big end bearing sizes.

S

“P1” 

X

 “P4” refer to the bearings shown in the

crankshaft illustration.

Selection of bearings:

For example, if the connecting rod “P

1

” and the

crankshaft web “P

1

” numbers are “5” and “1” re-

spectively, then the bearing size for “P

1

” is:

Bearing size for “P

1

”:

“P

1

” (connecting rod) – “P

1

”

(crankshaft) – 2 =
5 – 1 – 2 = 2 (Black)

BIG END BEARING COLOR CODE

–1

Violet

0

White

1

Blue

2

Black

3

Brown

16. Inspect:

S

Crankcase:
Cracks / damage 

!

 Replace.

Thoroughly wash the crankcase halves in a mild
solvent.
Thoroughly clean all the gasket surfaces and
crankcase mating surfaces.

S

Oil delivery passages
Obstruction 

!

 Blow out with compressed air.

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX10K

BOMBARDIER Ski-doo MX ZX 440 Operator'S Manual preview
Ski-doo MX ZX 440
Brand: BOMBARDIER Pages: 18

Brands by name

Popular brands

Load more brands