Yamaha RX10K Supplementary Service Manual Download

Page: 163 / 523

2-37

TRACK TENSION ADJUSTMENT/

SLIDE RUNNER INSPECTION

INSP

ADJ

CAUTION:

Track alignment

Shifted

to right

Shifted

to left

Left adjuster

Turn out

Turn in

Right adjuster

Turn in

Turn out

8 Slide runner

9 Track

Track metal

Gap

Forward

A RX10, RX10S

RX10R, RX10RS

B RX10M, RX10MS

c. Adjust the track deflection until the specified

amount is obtained.

Track deflection

More than

specified

Less than

specified

Left adjuster

Turn in

Turn out

Right adjuster

Turn in

Turn out

The adjusters should be turned an equal
amount.

Recheck the alignment and deflection. If
necessary, repeat steps (a) to (c) until the
specified amount is obtained.

Tighten the rear axle nut.

Nut (rear axle):
75 Nm (7.5 m

kg, 54 ft

lb)

SLIDE RUNNER INSPECTION

1. Inspect:

Slide runner

Cracks / damage / wear

Replace.

2. Measure:

Slide runner thickness

Out of specification

Replace.

Slide runner wear limit:

10 mm (0.39 in)

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands