Yamaha RX10K Page 135 Supplementary Service Manual Download

Page: 135 / 523

2-9

VALVE CLEARANCE ADJUSTMENT

INSP

ADJ

NOTE:

VALVE CLEARANCE ADJUSTMENT

Valve clearance adjustment should be made
on a cold engine, at room temperature.

When the valve clearance is to be measured
or adjusted, the piston must be at top dead
center (TDC) on the compression stroke.

1. Drain:

Coolant

2. Remove:

Cylinder head cover
Refer to “CYLINDER HEAD” in CHAPTER 5.

Timing plug

3. Measure:

Valve clearance
Out of specification

Adjust.

Valve clearance (cold)

Intake valve

0.11

0.20 mm

(0.0043

0.0079 in)

Exhaust valve

0.21

0.25 mm

(0.0083

0.0098 in)

Checking steps:

Turn the crankshaft clockwise.

When piston #4 is at TDC on the compression
stroke, align the TDC mark

on the A.C.

magneto rotor with the mark

on the A.C.

magneto cover.

Turn the crankshaft clockwise.

TDC on the compression stroke can be found
when the camshaft lobes are turned away from
each other.

Measure the valve clearance with a thickness
gauge

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands