Yamaha RX10K Supplementary Service Manual Download

Page: 184 / 523

2-58

CARBURETOR TUNING

INSP

ADJ

Trouble

Diagnosis

Adjustment

Poor performance at
mid-range speeds:

Momentary slow
response to the

Clogged or loose pilot jet

Remove the pilot jet, clean it with
compressed air, and then install it.

Make sure that the pilot jet is fully tightened.

throttle

Poor acceleration

Lean mixture

Overhaul the carburetors.

Poor performance at

Clogged air vent

Remove the air vent hose and clean it.

normal speeds:

Excessive fuel
consumption

Poor acceleration

Clogged or loose main jet

Remove the main jet, clean it with
compressed air, and then install it.

Make sure that the main jet is fully
tightened.

Overflow

Check and, if necessary, clean the float and
float valve.

Poor performance at

Starter valve is left open

Return the starter lever to its seated position

high speeds:

so that the starter valve is fully closed.

Power loss

Poor acceleration

Clogged air vent

Remove and clean the air vent.

Poor acceleration

Clogged or loose main air
jet

Remove the main jet, clean it with
compressed air, and then install it.

Make sure that the main jet is fully
tightened.

Clogged fuel line

Clean or replace the fuel line.

Dirty fuel tank

Clean the fuel tank.

Air leaks into the fuel line

Tighten or replace the fuel line joint.

Low fuel pump performance

Repair or replace the fuel pump.

Clogged fuel filter

Replace the fuel filter.

Clogged intake

Remove any obstructions (e.g., ice).

Abnormal combustion:

Lean mixture

Clean and adjust the carburetors.

Backfiring

Dirty carburetors

Clean the carburetors.

Dirty or clogged fuel line

Clean or replace the fuel line.

Overflow:

Clogged air vent

Clean the air vent.

Poor idling

Poor performance at
lo

mid range and

Clogged float valve

Disassemble and clean the float valve.

Do not scratch the valve seat.

low, mid-range, and
high speeds

Excessive fuel
consumption

Hard starting

Scratched or unevenly worn
float valve or valve seat

Clean or replace the float valve and valve
seat.

The valve seat and body must be replaced
as a set

Hard starting

Power loss

Broken float

Replace the float.

Power loss

Poor acceleration

Incorrect float level

Check and, if necessary, replace the following
parts:

Float tang

Float (entire assembly)

Arm pin

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands