Yamaha RX10K Supplementary Service Manual Download

Page: 349 / 523

7-9

CARBURETORS

CARB

NOTE:

FUEL LEVEL ADJUSTMENT

1. Measure:

Fuel level

Out of specification

Adjust.

Fuel level (below the line on the
float chamber):

3.0

4.0 mm (0.118

0.157 in)

Measurement steps:

Install the fuel level gauge

to the fuel drain

pipe

Fuel level gauge

90890-01312, YU-01312-A

Loosen the fuel drain screw.

Hold the fuel level gauge vertically next to the
line on the float chamber.

Measure the fuel level

on both sides of the

carburetor assembly.

The fuel level readings should be equal on both
sides.

2. Adjust:

Fuel level

Adjustment steps:

Remove the carburetor assembly.

Inspect the needle valve seat and needle
valve.

If either is worn, replace them as a set.

If both are fine, adjust the float height by bend-
ing the float tang

or the float.

Recheck the fuel level.

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands