1-5
SPECIAL TOOLS
GEN
INFO
FOR ENGINE SERVICE
S
Piston pin puller
P/ N: YU-01304 (for U.S.A. / Canada)
90890-01304 (for Europe)
This tool is used to remove the piston pin.
S
Rotor holding puller, attachment
P/ N: YU-33270 (for U.S.A. / Canada)
90890-01362 (for Europe)
P/ N: YM-33282
90890-04089
This tool is used to remove the magneto rotor.
S
Cooling system tester, adapter
P/ N: YU-24460-01 (for U.S.A. / Canada)
90890-01325 (for Europe)
P/ N: YU-33984 (for U.S.A. / Canada)
90890-01352 (for Europe)
This tester is used for checking the cooling system.
S
Oil filter wrench
P/ N: YU-38411 (for U.S.A. / Canada)
90890-01426 (for Europe)
This tool is needed to loosen or tighten the oil filter cartridge.
S
Carburetor synchronizer
P/ N: YU-8030 (for U.S.A. / Canada)
90890-03094 (for Europe)
This guide is used to synchronize the carburetors.
S
Compression gauge set
P/ N: YU-33223 (compression gage) (for U.S.A. / Canada)
90890-03081 (for Europe)
P/ N: YU-33223-3 (adapter) (for U.S.A. / Canada) (for Europe)
90890-04136 (for Europe)
These tools are used to measure engine compression.
S
Valve spring compressor set, quick release, attachment
P/ N: YM-04019 (valve spring compresser) (for U.S.A. / Canada)
90890-04019 (for Europe)
P/ N: YM-4108, YM-4114 (attachment) (for U.S.A. / Canada)
90890-04108, 90890-04114 (for Europe)
These tools are used-to remove or install the valve assemblies.
S
40 and 50 mm bearing driver.
Water pump seal installer.
P/ N: YM-4058 (40 and 50 mm bearing driver) (for U.S.A./Canada)
90890-04058 (for Europe)
P/ N: YM-33221 (water pump seal installer) (for U.S.A. / Canada)
90890-04078 (for Europe)
These tools are used to install the water pump seal.
Summary of Contents for RX10K
