Yamaha RX10K Supplementary Service Manual Download | Manualshive

Page: 139 / 523

background image

2-13

VALVE CLEARANCE ADJUSTMENT

INSP

ADJ

NOTE:

NOTE:

NOTE:

S

Install the new valve pad

1

and the valve lifter

2

.

S

Apply molybdenum disulfide oil to the valve
pad and the valve lifter.

S

The valve lifter must turn smoothly when ro-
tated by hand.

S

Install the valve lifter and the valve pad in the
correct place.

S

Install the exhaust and intake camshafts, tim-
ing chain and camshaft caps.

Camshaft cap bolt

10 Nm (1.0 m

S

kg, 7.2 ft

S

lb)

S

Refer to “CAMSHAFTS” in CHAPTER 4.

S

Lubricate the camshaft caps, camshaft lobes
and camshaft journals.

S

First, install the exhaust camshaft.

S

Align the camshaft marks with the camshaft
cap marks.

S

Rotate the crankshaft clockwise several turns
to seat the parts.

S

Measure the valve clearance again.

S

If the valve clearance is still out of specifica-
tion, repeat all of the valve clearance adjust-
ment steps until the specified clearance is ob-
tained.

6. Install:

S

Cylinder head cover
Refer to “CAMSHAFTS” in CHAPTER 5.

7. Install:

S

All removed parts

For installation, reverse the removal procedure.
Note the following points.

«
...
137
138
139
140
141
...
»

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX10K

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands