Yamaha RX10K Page 193 Supplementary Service Manual Download

Page: 193 / 523

2-67

Test the main jet
(performance & plug color)

Adjust the main jet size according to the
chart

Check STD settings

Carburetors

Spark plugs

Adjust the secondary clutch as required

High altitude
tuning OK

Adjust the size of the main jet

Re-test

Test the low speed setting

Check to see if the gearing is too high or low

Try high altitude settings

Decide if the problem is with the pilot jet
and adjust accordingly

Check the engagement speed and shift
performance

Adjust the primary clutch as required

Not OK

Adjust the engine
idle speed by
turning the stop
screw of carburetor.

Adjust the
engine idle
speed by
turning the
stop screw of
carburetor.

HIGH ALTITUDE TUNING

INSP

ADJ

HIGH ALTITUDE TUNING

To attain the best performance in high altitude conditions, carefully tune the snowmobile as outlined
below.

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Related manuals for RX10K

Brands by name

Popular brands