Yamaha RX10K Page 120 Supplementary Service Manual Download | Manualshive

Page: 120 / 523

background image

1

1-2

IMPORTANT INFORMATION

GEN

INFO

IMPORTANT INFORMATION

PREPARATION FOR REMOVAL AND DISASSEMBLY

1. Remove all dirt, mud, dust, and foreign material before removal

and disassembly.
While cleaning, take care to protect the electrical parts, such as
relays, switches, motor, resistors, controllers, etc., from high pres-
sure water splashes.

2. Use proper tools and cleaning equipment.

Refer to “SPECIAL TOOLS”.

3. When disassembling the machine, keep mated parts together.

This includes gears, cylinders, pistons, and other parts that have
been “mated” through normal wear. Mated parts must be reused
or replaced as an assembly.

4. During disassembly of the machine, clean all parts and place

them in trays in the order of disassembly. This will speed up as-
sembly time and help ensure that all parts are reinstalled correctly.

5. Keep all parts away from any source of fire.

6. Be sure to keep to the tightening torque specifications. When

tightening bolts, nuts, and screws, start with those that have larger
diameters, and proceed from the inside to the outside in a criss-
cross pattern.

ALL REPLACEMENT PARTS

We recommend using genuine Yamaha parts for all replacements.
Use oil and grease recommended by Yamaha for assembly and ad-
justments.

«
...
118
119
120
121
122
...
»

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RX10K

LYNX Radien 2019

Brand: BRP Pages: 229

Brand: Yamaha Pages: 90

Legend 800 2002

Brand: Ski-Doo Pages: 30

Formula MX 1985

Brand: Ski-Doo Pages: 50

1982 Blizzard 9500

Brand: Ski-Doo Pages: 42

Brand: Ski-Doo Pages: 52

Skandic SWT 2013

Brand: Ski-Doo Pages: 135

MX Z 800 2145 2002

Brand: Ski-Doo Pages: 123

2002 Mach Z STD

Brand: Ski-Doo Pages: 115

REV XP 2008 Series

Brand: Ski-Doo Pages: 155

Brand: Ski-Doo Pages: 926

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands