1-3
IMPORTANT INFORMATION
GEN
INFO
CAUTION:
GASKETS, OIL SEALS, AND O-RINGS
1. All gaskets, seals, and O-rings should be replaced when an en-
gine is overhauled. All gasket surfaces, oil seal lips, and O-rings
must be cleaned.
2. Properly oil all mating parts and bearings during reassembly. Ap-
ply grease to the oil seal lips.
LOCK WASHERS/ PLATES AND COTTER PINS
All lock washers / plates
1
and cotter pins must be replaced if they
are removed. Lock tab(s) should be bent along the bolt or nut flat(s)
after the bolt or nut has been properly tightened.
BEARINGS AND OIL SEALS
Install the bearings
1
and oil seals
2
with their manufacturer’s
marks or numbers facing outwards. (In other words, the stamped let-
ters must be on the side exposed to view.) When installing oil seals,
apply a light coating of lightweight lithium base grease to the seal lips.
Oil the bearings liberally when installing.
Do not use compressed air to spin the bearings dry. This causes
damage to the surface of the bearings.
CIRCLIPS
All circlips should be inspected carefully before reassembly. Always
replace piston pin clips after one use. Replace misshapen circlips.
When installing a circlip
1
, make sure that the sharp edged corner
2
is positioned opposite to the thrust
3
it receives. See the section-
al view.
4 Shaft
LOCTITE
After installing fasteners that have LOCTITE
applied, wait 24 hours
before using the machine. This will give the LOCTITE
time to dry
properly.
Summary of Contents for RX10K
