Yamaha RX10K Supplementary Service Manual Download Page 231

Page: 231 / 523

4-15

SECONDARY SHEAVE

POWR

NOTE:

Adjustment steps:

Disassemble the secondary sheave.

Remove the bolts and original shims

Install new shims of the proper thickness and
reassemble the secondary sheave.

Measure the secondary sheave clearance
again.
Repeat these steps until the clearance is
within specification.

Yamaha recommends keeping the original
shims.

Shims:

Part number

Thickness

90201-061H1

0.5 mm (0.02 in)

90201-06037

1.0 mm (0.04 in)

INSTALLATION

1. Lubricate:

Splines (fixed sheave)

Recommended grease:

ESSO beacon 325 grease or
Aeroshell grease #7A

2. Tighten:

Secondary sheave bolt:

64 Nm (6.4 m

kg, 46 ft

lb)

3. Adjust:

V-belt position
Refer to “DRIVE V-BELT” in CHAPTER 2.

Sheave offset

Secondary sheave free play (clearance)
Refer to “SHEAVE DISTANCE AND OFF-
SET ADJUSTMENT” in CHAPTER 2.

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Search results

Summary of Contents for RX10K

Reviews:

Brands by name

Popular brands

Yamaha RX10K, Supplementary Service Manual

Search results

Summary of Contents for RX10K

Reviews:

Brands by name

Popular brands