manualshive.com logo in svg

Yamaha RX10K, Supplementary Service Manual

Share
Download
Yamaha RX10K Supplementary Service Manual Download Page 312

5-45

CRANKCASE

ENG

NOTE:

CAUTION:

NOTE:

NOTE:

REMOVAL

1. Remove:

S

Crankcase bolts

S

Place the engine upside down.

S

Loosen each bolt 1 / 4 of a turn at a time, in
stages and in a crisscross pattern. After all of
the bolts are fully loosened, remove them.

S

Loosen the bolts in decreasing numerical or-
der (refer to the numbers in the illustration).

S

The numbers embossed on the crankcase in-
dicate the crankcase tightening sequence.

2. Remove:

S

Lower crankcase

Tap on one side of the crankcase with a soft-
face hammer. Tap only on reinforced por-
tions of the crankcase, not on the crankcase
mating surfaces. Work slowly and carefully
and make sure that the crankcase halves
separate evenly.

3. Remove:

S

Dowel pins

S

Crankshaft journal bearing

Identify the position of each crankshaft journal
lower bearing so that it can be reinstalled in its
original place.

4. Remove:

S

Connecting rod cap 

1

S

Big end bearing

Identify the position of each big end bearing so
that it can be reinstalled in its original place.

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands