2-36
TRACK TENSION ADJUSTMENT
INSP
ADJ
WARNING
TRACK TENSION ADJUSTMENT
A broken track or track fittings, and debris
thrown by the track could be dangerous to
an operator or by standers. Observe the fol-
lowing precautions.
S
Do not allow anyone to stand behind the
machine when the engine is running.
S
When the rear of the machine is raised to
allow the track to spin, a suitable stand
must be used to support the rear of the ma-
chine. Never allow anyone to hold the rear
of the machine off the ground to allow the
track to spin. Never allow anyone near a ro-
tating track.
S
Inspect the condition of the track frequent-
ly. Replace the track if it is damaged to a
level where the fabric reinforcement mate-
rial is visible.
1. Lift the rear of the machine onto a suitable
stand to raise the track off the ground.
2. Measure:
S
Track deflection
a
Using a spring scale
1
, pull down on the
center of the track with 100 N (10 kg, 22 lb) of
force.
Out of specification
!
Adjust.
Track deflection:
25
X
30 mm (0.98
X
1.18 in)
3. Adjust:
S
Track deflection
Adjustment steps:
S
Place the machine onto a suitable stand to
raise the track off of the ground.
S
Loosen the rear axle nut
1
.
a. Start the engine and rotate the track once or
twice. Stop the engine.
b. Check the track alignment with the slide run-
ner
2
. If the alignment is incorrect, turn the
left and right adjusters to adjust.
Summary of Contents for RX10K
