manualshive.com logo in svg

Yamaha RX10K, Supplementary Service Manual

Share
Download
Yamaha RX10K Supplementary Service Manual Download Page 171

2-45

BATTERY INSPECTION

INSP

ADJ

Relationship between the open-circuit voltage
and the charging time at 20

_

C

Open-circuit voltage (V)

These values vary with the temperature, the condition of
the battery plates, and the electrolyte level.

13.0

12.5

12.0

11.5

5

6.5

10

Charging time (hours)

NOTE:

CAUTION:

NOTE:

Since MF batteries are sealed, it is not possible
to check the charge state of the battery by mea-
suring the specific gravity of the electrolyte.
Therefore, the charge of the battery has to be
checked by measuring the voltage at the battery
terminals.

1. Disconnect:

S

Battery leads
(from the battery terminals)

First, disconnect the negative lead 

1

, then

the positive lead 

2

.

2. Remove:

S

Battery

3. Inspect:

S

Battery charge

Inspection steps:

S

Connect a pocket tester to the battery termi-
nals.

Tester positive lead 

!

battery positive 
terminal

Tester negative lead 

!

battery negative 
terminal

S

The charge state of a MF battery can be
checked by measuring its open-circuit voltage
(i.e., the voltage when the positive terminal is
disconnected).

S

No charging is necessary when the open-cir-
cuit voltage equals or exceeds 12.8 V.

S

Check the charge of the battery, as shown in
the charts and the following example.

Example

S

Open-circuit voltage = 12.0 V

S

Charging time = 6.5 hours

S

Charge of the battery = 20 

X

 30%

Summary of Contents for RX10K












































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands