Xantrex XKW 12-150, Operating Manual

Page: 15 / 90

Revision A
xiii
List of Figures
Figure 1.1 Power Supply Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 1.2 Power Supply Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 2.1 Shipping or Storage Carton Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2.2 Stripped Wire Installed in Strain Relief . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 2.3 Connector J3 Configuration for Local Operation . . . . . . . . . . . . . . . . . 35
Figure 2.4 Maximum Load Wire Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 2.5 Single Load with Local Sensing (Default) . . . . . . . . . . . . . . . . . . . . . . 40
Figure 2.6 Single Load with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 2.7 Multiple Loads with Local Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 2.8 Multiple Loads with Remote Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 2.9 Local Mode Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 2.10 Connecting Remote Sense Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3.1 J3 Program, Sense, and Monitor Connector Description . . . . . . . . . . 49
Figure 3.2 Internal Jumpers and Switch (Default Settings Shown). . . . . . . . . . . . 50
Figure 3.3 Locating Jumpers, Switch, and Connector . . . . . . . . . . . . . . . . . . . . . 51
Figure 3.4 Programming Output Voltage and Current Limit . . . . . . . . . . . . . . . . . 56
Figure 3.5 Programming Output Voltage with a 0-5Vdc Source . . . . . . . . . . . . . . 57
Figure 3.6 Programming Output Voltage with a 0-10Vdc Source . . . . . . . . . . . . . 58
Figure 3.7 Programming Output Voltage with a 0-1mA Source . . . . . . . . . . . . . . 58
Figure 3.8 Programming Output Voltage with a 5k ohm Resistance . . . . . . . . . . 59
Figure 3.9 Programming Output Current Limit with a 0-5Vdc Source. . . . . . . . . . 59
Figure 3.10 Programming Output Current Limit with a 0-10Vdc Source. . . . . . . . . 60
Figure 3.11 Programming Output Current Limit with a 0-1mA Source . . . . . . . . . . 61
Figure 3.12 Programming Output Current Limit with a 5k ohm Resistance . . . . . . 61
Figure 3.13 Remote Programming of OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 3.14 Remote Programming of OVP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Figure 3.15 Using Shutdown with a TTL Compatible (Positive Logic) . . . . . . . . . . 66
Figure 3.16 Using Shutdown with a TTL Compatible (Negative Logic) . . . . . . . . . 66
Figure 3.17 Using Shutdown with an AC or DC Input (Positive Logic) . . . . . . . . . . 67
Figure 3.18 Using Shutdown with an AC or DC Input (Negative Logic) . . . . . . . . . 68
Figure 3.19 Using Shutdown with Contact Closure of a Normally OPEN Relay. . . 69
Figure 3.20 Using Shutdown with Contact Closure of an OPEN Relay . . . . . . . . . 70
Figure 3.21 Using Shutdown with Contact Closure of a CLOSED Relay . . . . . . . . 70
Figure 3.22 Using Shutdown with Contact Closure of a CLOSED Relay . . . . . . . . 71
Figure 3.23 Series Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . . 74
Figure 3.24 Parallel Operation of Multiple Supplies . . . . . . . . . . . . . . . . . . . . . . . . 75
TM-25OP-01XN.book Page xiii Monday, April 5, 2004 8:58 AM