Wfly WFT08X Instruction Manual Download | Manualshive

Page: 54 / 118

background image

16. TIMER

The flight time of every helicopter is different according to
the different tank of fuel, engine, ESC, etc. Timer function
can alarm you to land before the fuel lacks.
The transmitter can set 3 timers (A, B, C). The longest time
can be set as MM99SS59. The countdown timer can alarm
user before 10 minutes. The alarm will become 2S/1S from
1S/1S in the last 10 seconds. When the countdown timer is
0, the time will add up.
The timer can be seen in the opening screen. Any switch
can be set to control the begin and stop of the time.

Setting Method:

Use up/down keys to select

TIMER

, OK button is to enter

editing.

Steps:

1. Use direction keys to select editing part.
2. Set timer. WFT08 can set 3 timers (A, B, C).
3. Use +/- keys to set MM..SS... Long press OK can back
to default.
4. Use +/- keys to set model.
5. Use +/- keys to set control(CTRL).
6. Use +/- keys to set the position which can active this function.
7. Press EXIT after setting.

WFT08X

INSTRUCTION

48

HELICOPTER

«
...
52
53
54
55
56
...
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: Lawler Pages: 5

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

TEMP2000 Series

Brand: Samwontech Pages: 91

Brand: Warren rupp Pages: 18

Brand: Yamaha Pages: 100

Brand: Vanderbilt Pages: 2

Brand: Xylem Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands