Wfly WFT08X Instruction Manual Download | Manualshive

Page: 52 / 118

background image

14. THROTTLE HOLDING SETTING

Setting Method:

Use up/down keys to select

Throttle holding setting

, OK to

enter editing.

Steps:

1. Use direction keys to select editing part.
2. Use +/- keys to activate or inhibit the mix function.
3. Use +/- keys to set the throttle holding position. Long press OK
can back to default.
4. Use +/- keys to active or inhibit the rudder mix.
5. Use +/- keys to set the mix rate (offset). Long press OK can
back to default.
6. Press EXIT after setting.

This function can make the throttle servo operating at a low
speed position at the end of a flight. The range is between
-75% and +75%.
User can set the mix function with rudder under the throttle
holding state and the mix rate (offset).
This function switch can be found in “

Fly model switch

”

.

WFT08X

INSTRUCTION

46

HELICOPTER

«
...
50
51
52
53
54
...
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: wattio Pages: 20

Brand: MADRIX Pages: 36

Brand: Campbell Pages: 3

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: ICM Controls Pages: 2

Brand: WAM Pages: 62

Brand: walimex Pages: 7

Brand: Walchem Pages: 2

Brand: Walchem Pages: 73

Brand: Walchem Pages: 126

Brand: wallas Pages: 2

Brand: C&C Pages: 17

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands