Wfly WFT08X Instruction Manual Download | Manualshive

Page: 60 / 118

background image

(5). TRIM OFFSET SETTING

This function is to adjust the servo trim at hovering state.
This function is used to automatically change the trim of a
helicopter, for example, when transitioned from hover to
flying at high speed. A clockwise-rotation rotor helicopter
tends to drift to the right at high speed, so an aileron offset
may be applied to offset the helicopter to the left.
The necessary elevator offset varies with model geometry,
so it must be determined by noting collective pitch changes
at high speed.
The rudder offset is affected by both revolution mixing and
trim lever movement while in the offset function.

Setting Method:

Use up/down keys to select

Trim offset setting

, OK to enter

editing.

Steps:

1. Use direction keys to select editing part.
2. Use +/- keys to active or inhibit “Mix”.
3. Use +/- keys to

s

et the control switch “CTRL”.

4. Use +/- keys to set the control switch position “Pos“.
5. Use +/- keys to set the channel, eg: aileron, elevator,
direction etc.
6. Use +/- keys to set the mix rate “Rate”. Long press OK can
back default.
7. Press EXIT after setting.

WFT08X

INSTRUCTION

54

HELICOPTER

«
...
58
59
60
61
62
...
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: Zolix Instruments Pages: 22

Brand: Rain Bird Pages: 48

Brand: Unitech Pages: 11

Brand: B meters Pages: 10

Brand: Samson Pages: 52

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: ZIGBEE Pages: 5

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: Union Instruments Pages: 63

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: GI.BI.DI Pages: 60

DuoControl Signal 111

Brand: Tormatic Pages: 3

Hydropan-Single

Brand: ETNA Pages: 12

Brand: u-blox Pages: 157

Brand: Airlow Pages: 20

Brand: Eaton Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands