Wfly WFT08X Instruction Manual Download

Page: 13 / 118

The receiver is used for WFT09(S)/08X transmitter.

WFR08-P 8 Channel Software decoding Receiver (PPM)

WFT08X

INSTRUCTION

RECEIVER

MODEL NO.: WFR08

TYPE: 8CH Software decoding

PPM

POWER SUPPLY: 1.2V x 4 (4.8V)
CURRENT DRAIN: 20mA
WEIGHT: 19 g
DIMENSION: 44.88mm x27.90mm x16.39mm
BAND: 35, 36, 40, 41, 72

75MHz

There

the

function

fail

safe

．

AUX1

：

Auxiliary channel 1 (Channel 7)------------------

．

AUX2

：

Auxiliary channel 2 (Channel 8)-------------------

．

AIL

：

Aileron (Channel 1)-----------------------------------

．

ELE

：

Elevator (Channel 2)--------------------------------

．

THR

：

Throttle (Channel 3)----------------------------------

．

RUD

：

Rudder (Channel 4)----------------------------------

．

Power

：

Input +4

6V--------------------------------------

The

setting

for

fail

safe

Receiver connected to the battery (transmitter don

opened), wait 16 seconds or so, the red

LED flashes, make

sure

every

channel

has

been

putting

the

location

you

need

then

open

the

transmitter(that is

the

data

receiver

output

after

the

out

control protection , for example:

throttle is

set

to 10%, the direction is set to 60%, then when entering the out-of-control

protection

the

receiver

output

data is

throttle

10%, the direction 60%)

Note

you

need

35MHz

75MHz

WFLY

will

supply

receiver

and

module

．

GYR

：

Landing Gear/Gyro (Channel 5)--------------------

．

PIT

：

Pitch (Channel 6)------------------------------ ----------

Summary of Contents for WFT08X























































































































Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands

Wfly WFT08X, Instruction Manual

Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands