Wfly WFT08X Page 105 Instruction Manual Download | Manualshive

Page: 105 / 118

background image

ADVANCED function introduction

WFT08X

INSTRUCTION

1. CURVE SETTING

There are 2 kinds of setting, Normal and Advanced.

99

AIRPLANE

1. Setting introduction

Curve setting is one of the functions of WFT08X. We will make
detail description here. You can refer to this detail description
for the other functions which relates to the curve setting.
There are two kinds of curve setting mode: normal setting and
advanced setting.
Normal setting:

7 points curve setting. You can set the curve by

setting the

7

points value.

Advanced setting: you can add or delete the curve point.
Advanced curve can be added at most 7 points, at least 2 points.
You can not only set the value of each point, but also the position
of each point.

2. Setting method

Turn on the transmitter, press menu, find “ADVANCED”, select
“curve setting”.
There are two modes: normal, advanced.

Normal curve setting: 7 points curve setting. You can edit the
curve point in the left pane.
1. Use left/right direction button to select the editing point. The
curve point is marked by a dashed line.
2. Use +/- button to set the value. Press OK button for a while can
back to default. You can set the 7 points.
3. Press EXIT after setting.

«
...
103
104
105
106
107
...
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: OmarLift Pages: 14

Brand: Ultra Start Pages: 20

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: Calsense Pages: 74

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: Daikin Pages: 5

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: V2 Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands