Wfly WFT08X Instruction Manual Download | Manualshive

Page: 117 / 118

background image

16. GYRO SENS SETTING

User can adjust the gyro sensitivity by transmitter,
AVCS gyro (GY) and normal gyro (STD).
Gyro sensitivity switch plug should plug in the fifth channel of
receiver. The auxiliary channel CH 5 won’t have any function
now. User can set sensitivity switch from switch A to F, and also
fly model (NORM, IDLE1,2,3).

Setting Method:

Use up/down keys to select

GYRO sens setting

, OK to enter

editing.

Steps:

1. Use direction keys to select editing part.
2. Use +/- keys to set fly model at “CHANNEL”.
3. Use +/- keys to on/disable“Mix”.
4. Use +/- keys to set control switch at “CTRL”.
5. Use +/- keys to set the switch position when the function is
active.
6. Use +/- keys to set the “Rate”. Long press OK is back to
default.
7. Press EXIT after setting.

111

WFT08X

INSTRUCTION

AIRPLANE

«
...
115
116
117
118
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: Valve Concepts Pages: 15

Brand: Harmonic Drive Pages: 85

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

Brand: RADEMACHER Pages: 68

Brand: SYCLOPE electronic Pages: 40

Brand: Timotion Pages: 10

Brand: Climatisation Pages: 52

Brand: TECOM Pages: 8

Brand: GEM Pages: 17

Brand: Inkel Pages: 12

Brand: SILENTRON Pages: 20

Brand: MacroAir Technologies Pages: 32

Brand: IMG STAGELINE Pages: 14

Brand: VAT Pages: 77

Brand: Z-Wave Pages: 44

HydroGuard 1430 Series

Brand: Powers Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands