Wfly WFT08X Instruction Manual Download | Manualshive

Page: 18 / 118

background image

Allen key

Top thread

stick head

Stick

Put the stick head cover the control rod
on the left and right sides,don't twist down
the stick head to the bottom, and then put
top thread with allen key to adjust the
height you need.

Adjust the height higher: first make the top
thread loose with the allen key, then twist
the stick head up, then, make the top
thread tighten with allen key, Ok, the stick
head was turned up.

Twist the top thread down

from here, the height of the
stick head depends on the
depth of the top thread.

Adjust the height lower: first make the

top thread loose with the allen key, then
twist the stick head down, then, make the
top thread tighten with allen key, Ok, the
stick head was turned down.

steps

:

1

Put the stick head on the stick.

2

Put the top thread in the stick head with allen key.

3

.

Adjust top thread in the stick head with allen key to fix the height

of

the stick head.

Adjust

the

stick

head

:

12

«
...
16
17
18
19
20
...
»

Summary of Contents for WFT08X























































































































Reviews:

No comments

Related manuals for WFT08X

Brand: ABATEC Pages: 8

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: WAGNER Pages: 60

Brand: K&G GROEP Pages: 27

Brand: CAME Pages: 2

Brand: CalAmp Pages: 13

Brand: J+J Pages: 4

Brand: Val Controls Pages: 6

Brand: ZKTeco Pages: 13

Brand: UniPi Technology Pages: 4

Brand: Eaton Pages: 448

Brand: Eaton Pages: 57

Brand: cinetto Pages: 56

Brand: Daihan Scientific Pages: 11

Brand: Tech 21 Pages: 2

Brand: Acumen Pages: 6

Brand: PCB Piezotronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands