Wfly WFT08X Instruction Manual Download

Page: 11 / 118

The receiver is used for all WFLY transmitters.

WFR09S 9 Channel Receiver

．

AIL

：

Aileron (Channel 1)-------------------------

．

ELE

：

Elevator (Channel 2)----------------------

．

THR

：

Throttle (Channel 3)------------------------

．

RUD

：

Rudder (Channel 4)------------------------

．

GYR

：

Landing Gear/Gyro (Channel 5)----------

．

PIT

：

Pitch (Channel 6)------------------------------

．

AUX1

：

Auxiliary channel 1 (Channel 7)----------

．

AUX2

：

Auxiliary channel 2 (Channel 8)-----------

．

Power

：

Input 4.8-6V----------------------------------

RECEIVER

MODEL NO.: WFR09S

TYPE: 9 CH PPM/PCMS 1024/PCMS 4096
POWER SUPPLY: 4.8-6V
CURRENT DRAIN: 30mA
RECEIVER

SENSITIVITY

: -

97dBm

BAND: 2.400GHz-2.4835GHz

WFT08X

INSTRUCTION

This

receiver

has

fail

safe

function

Characteristic

Can effectively select the best signal

Enhance the reliability

Improve

the

response

speed

;

Enhance the anti-interference

Increased use of

range

(There are 9 rows needles, 3 needles in each row,
from the top needle to the bottom, the 3 needles are PCMS/PPM pulse, +5V and Ground.)

Summary of Contents for WFT08X























































































































Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands

Wfly WFT08X, Instruction Manual

Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands