Wfly WFT08X Instruction Manual Download

Page: 72 / 118

WFT08X

INSTRUCTION

B. SYS SETTING

Press Menu and turn on the power switch, the LCD displays the
following:

1. MODEL SELECTTING
2. MODEL NAME
3. MODEL SETTING
4. ATL
5. AIL-2
6. MODULATION SETTING
7. STICK SETTING
8. REST SETTING
9. SEND DATA
10. RECEIVE DATA
11. CONTRAST SETTING
12. ENGINEER MODEL
13. ABOUT
14. LANGUAGE

Setting method:

1. Use direction keys to select the
editing part, use up/down keys to
select function item. Left/right direction
keys to switch pages.

2. Press OK to enter submenu.
The submenu function is described in
the next chapter.

3. Press EXIT key to go back to previous
menu and the data is set automatically.

C. ADVANCED

1. Enter “NORMAL SETTING”, use direction keys to switch
pages, select “ADVANCED”.
Press OK to enter.

Setting method:

1. Use direction keys to select the editing part,
use up/down keys to select function item.
Left/right direction keys to turn page.

2. Press OK to enter submenu. The submenu function is described
in the next chapter.

3. Press EXIT key to go back to previous menu and the data is
set automatically.

AIRPLANE

Summary of Contents for WFT08X























































































































Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands

Wfly WFT08X, Instruction Manual

Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands