Wfly WFT08X Instruction Manual Download

Page: 30 / 118

This function is to set the center, high and low points of four sticks
when users change the mode I or mode II by themselves.

Setting Method:

Press Menu and turn on the transmitter to enter “SYS SETTING”
Use up/down button to select “

ADJUSTMENT

”, OK button is

to enter editing.

Steps:

1. Use direction button to select the editing

part.

Take

the

aileron

adjustment

for

example

2. Make the

stick in the mid-point location

Press OK button

to select any stick you

want to adjust.

3. Select into the Figure 2, when the "center" highlights, press the "ok"
button directly (the mid-point has been

adjusted), then enter the high

adjust.

The "high” highlights,

take

the

stick

gently

in the right side

(throttle /elevator in the top, aileron / rudder in the right),press "ok"
button ( the max.

adjust is OK), enter the

low

adjustment.

5.The "low" highlights,

take the

stick

gently

in the left side (throttle

/elevator in the bottom, aileron / rudder in the left),press "ok" button
(the min.

adjust is OK).

6. Press OK or RESET to confirm the record or reset.

7. If the record is wrong, press OK will back to step 3.

8.Adjustment

WFT08X

INSTRUCTION

HELICOPTER

Summary of Contents for WFT08X























































































































Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands

Wfly WFT08X, Instruction Manual

Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands