Wfly WFT08X Instruction Manual Download

Page: 15 / 118

FLYING SAFETY WARNINGS

Dangers

If you use it without proper operation, it is possible that you

hurt yourself or others seriously or may even cause death.

Warnings

If you use it without proper operation, it may cause harm to

you and others as well as it could cause damage to third
party property.

Notices

If you use it without proper operation, it may cause you to

hurt slightly or damage things , but it won't hurt you seriously
normally.

Special Symbol Instruction

Forbiddance! Obligation!

Warning!

Flying Notice

(warning)

Same frequencies can't fly at the same time.

Two radios transmitting on the same frequency will
cause an airplane to crash, even when the modulation
(AM, FM, PCM) is different.

Do not fly at night , during rain or in strong wind, as
you risk damaging your equipment. This device is not
water-proof.

Please check that all servos work properly and
eliminate all problems before operating your model.
(If the radio bounces after turning off the power, there
may be some disturbances, in this case, please
change your channel by exchange crystals)

Checking

Notices

Always

turn on the transmitter first, then the receiver. When

turning off the system, turn off the receiver first, then the
transmitter.

Notices

Children under 14 must be accompanied and instructed by

adults!

To use the product safely, please pay attention to the instructions
as follows.
Please pay special attention to the symbol as follows:

WFT08X

INSTRUCTION

Summary of Contents for WFT08X























































































































Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands

Wfly WFT08X, Instruction Manual

Search results

Summary of Contents for WFT08X

Reviews:

Related manuals for WFT08X

Brands by name

Popular brands