Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 81

Page: 81 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 81 of 131

WHM Cascade

→

Cascade Comm Parameters

Menu Item
Display

Available Choices or Limits

Default

Minimum

Maximum

Unit
Address

The address in the WHM Cascade of the current unit.

Min
Address

WHM Manager only:

The minimum address in the WHM cascade

Max
Address

WHM Manager only:

The maximum address in the WHM cascade

Cascade
Baud Rate

9600, 19200, 38400, 57600

9600

The rate at which information is transferred in a communication channel.

Network
Timeout

999

30 sec.

The timeout value before a Modbus Fault is declared due to no response from the
WHM Manager unit or (if a Manager) from the BAS

Error
Threshold

The number of Modbus Comm errors allowed before invoking a Modbus Comm Fault.

Comm Error
1- 8

0 0 0 0 0 0 0 0

Read Only

WHM Manager only:

Displays the number of comm errors on Clients 1

–

Comm Error
9- 16

0 0 0 0 0 0 0 0

Read Only

WHM Manager only:

Displays the number of comm errors on Clients 9

–

SSD Address

250

The Client/Client Device address (for backwards compatibility).

SSD Temp
Format

Degrees or Points

Degrees

WHM Manager only: Choose Degrees or Points

Unit Failsafe
Mode

Constant Setpt or Shutdown

Constant Setpt

Specifies the plant’s operating mode if there is a loss of communication with BAS

Unit Failsafe
Setpoint

170

160

Specifies the plant’s setpoint if there is a loss of communication.

Time &
Date Sync

Enabled/Disabled

Enabled

WHM Manager only:

If Enabled, all WHM Client units will synchronize time and date

with the WHM Manager.

WHM Min
Units

WHM Manager only

–

The minimum number of

unit’s valve open all the time

in the

WHM cascade (may differ from

Min Address

)

WHM Max
Units

WHM Manager only:

The maximum number of units in the WHM cascade (it can differ

from

Max Address

)

WHM On
Timeout

15 Sec

300 Sec

60 Sec

WHM Manager only

–

Specifies the time the WHM Manager must wait for a Client unit

to turn on.

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands