Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 2

Page: 2 / 131

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 2 of 131

Installation, Operation & Maintenance Manual

Centurion Water Heater

TABLE OF CONTENTS

TABLE OF CONTENTS ........................................................................................... 2

FOREWORD 5

SECTION 1: SAFETY PRECAUTIONS...................................................................... 8

1.1 WARNINGS & CAUTIONS ................................................................................................... 8

1.2 EMERGENCY SHUTDOWN ................................................................................................ 9

1.3 PROLONGED SHUTDOWN ................................................................................................ 9

1.4 IMPORTANT

– FOR MASSACHUSETTS INSTALLATIONS ...............................................10

SECTION 2: INSTALLATION ............................................................................... 12

2.1 RECEIVING THE UNIT .......................................................................................................12

2.2 UNPACKING .......................................................................................................................12

2.3 SITE PREPARATION .........................................................................................................12

2.3.1 Installation Clearances ................................................................................................................... 13
2.3.2 Setting The Unit .............................................................................................................................. 15
2.3.3 Housekeeping Pad Requirements .................................................................................................. 15

2.4 LIFTING PROVISIONS .......................................................................................................16

2.5 PIPING CONNECTIONS .....................................................................................................17

2.6 TEMPERATURE AND PRESSURE RELIEF VALVE INSTALLATION ................................20

2.7 CONDENSATE DRAIN AND PIPING ..................................................................................21

2.8 GAS SUPPLY PIPING ........................................................................................................22

2.9 AC ELECTRICAL POWER WIRING....................................................................................25

2.9.1 Power Panel Locations ................................................................................................................... 25
2.9.2 Electrical Power Panel Internal Components ................................................................................. 25

2.10 FIELD CONTROL WIRING

– I/O BOARD .........................................................................26

2.10.1 I/O Board Connections ................................................................................................................. 28

2.11 FLUE GAS VENT INSTALLATION ....................................................................................31

2.11.1 Massachusetts Installations ......................................................................................................... 31

2.12 COMBUSTION AIR ...........................................................................................................32

2.12.1 Ducted Combustion Air ................................................................................................................ 32

2.13 SEQUENCING ISOLATION VALVE INSTALLATION ........................................................32

2.14 WATER HEATER PUMP RELAY ......................................................................................34

2.15 NEXT STEPS ....................................................................................................................34

SECTION 3: EDGE CONTROLLER OPERATION ..................................................... 35

3.1 LOGIN AND PASSWORD ENTRY ......................................................................................36

SECTION 4: START SEQUENCE ........................................................................... 37

4.1 START SEQUENCE ...........................................................................................................37

4.2 START/STOP LEVELS .......................................................................................................40

4.3 START/STOP LEVELS

– AIR/FUEL & ENERGY INPUT .....................................................41

SECTION 5: INITIAL START-UP ........................................................................... 42

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands