Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 36

Page: 36 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 3: EDGE CONTROLLER OPERATION

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 36 of 131

3.1 LOGIN AND PASSWORD ENTRY

The Edge Controller has multiple levels of password protection.

Level Password

Description

No password

The default. Many parameters are visible but “Read Only.”

159

Allows for routine maintenance by PVI trained technicians.

A higher-level password for Master Technicians is distributed on an individual basis.

To enter a password:

1. On the Edge Controller, go to

Main Menu

→

Advanced Setup

→

Access

. The

Enter

Password

screen appears.

2. Use the number keypad to enter the password then press

Save

. You will have access to the

functionality associated with the level of the password entered.

Figure 3-2: Enter Password Screen

3. Once you have successfully logged into the system, the

Main Menu

appears. All Edge

functionality is accessed through one of the six

Main Menu

items.

Figure 3-3: Edge Controller Main Menu

NOTE:

Full instructions for the Edge Controller are in the

Edge Controller Manual

(OMM-0161).

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands