Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 100

Page: 100 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 9: O2 TRIM OPERATION

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 100 of 131

The Edge Controller displays following statuses in the

Trim Status

parameter on the

Advanced Setup

→

Performance

→

Trim

→

Trim Status

screen.

Trim Operation Interruption Errors

Status Messages

Description

Action

Idle

O2 Trim is not active

None-Normal Operation

O2 Wait

O2 Trim is waiting for to initiate the
process

None-Normal Operation

Hunt

O2 Trim is looking for target

None-Normal Operation

WaitLock

O2 Trim found the target, waiting for
system to stabilize

None-Normal Operation

Locked

O2 Trim is ready to start the process

None-Normal Operation

Adjust

O2 trim is correcting the system

None-Normal Operation

Settle

System is settling after the correction

None-Normal Operation

Done

O2 Trim is successfully completed

None-Normal Operation

BV Hi Err

Trim operation exceeds blower

voltage limits

Check air filter, gas regulator,
combustion calibration

BV Lo Err

Check sensor calibration; it may need to
be replaced

Max Iter

Trim Operation reached maximum

iteration. Wait and try again

Check sensor calibration for inaccuracies
Increase gain or iteration attempts

Outlet Out of Rng

Outlet temp is outside of temperature
range

None-Normal Operation

FR Out of Rng

Fire Rate is not within track range
during trim operation

None

–

Steady State has not been

achieved

O2 Trim in SP limit Unit is in setpoint limiting

None

–

System is near the high temp

limit.

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands