Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 84

Page: 84 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 8: WATER HEATER MANAGEMENT

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 84 of 131

Operating Controls

→

Valve Configuration Parameters

Menu Item Display

Available Choices or Limits

Default

Minimum

Maximum

Select Output

Aout 2

Read Only

Select the output you want to configure.

Output Signal Type

Current

Read Only

Select the output signal type of the selected output.

Control Mode

On/Off

Read Only

Select the Control Mode for the selected output (Standard Setup)

Valve Feedback

Enabled/Disabled

Disabled

Allows Valve Feedback functionality to be enabled;

Valve Feedback Status

appears.

Valve Feedback Timer

30 Sec.

240 Sec.

60 Sec.

The amount of time for the valve to open before returning an error.

Valve Feedback Status

Open, Close

Read Only

Displays the status of the selected valve.

Figure 8-9: Operating Controls: Valve Configuration Screen

Operating Controls

→

Lead/Lag Control Parameters

Menu Item Display

Available Choices or Limits

Default

Minimum

Maximum

Lead/Lag Setting

Run Hours, Unit Size,
Select Lead/Lag

Run Hours

Specify how the Lead and Lag units will be selected.

Run Hours

225

Specify the number of hours after which the Lead unit is rotated.

Lead Unit

Specify the address of the Lead unit.

Lag Unit

Specify the address of the Lag unit.

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands