Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 62

Page: 62 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 6: SAFETY DEVICE TESTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 62 of 131

6.8.2 Blocked Inlet Switch Test

This test will be run in simulated fire mode, with the Blocked Inlet switch isolated from the rest of
the control circuitry.

Set the Controller’s

Enable/Disable

switch to

Disable

2. Remove the air filter (see Figure 6-7, above).

WARNING:

THE BLOWER SUCTION IS VERY STRONG AND CAN PULL NEARBY

OBJECTS INTO THE FAN BLADES!

3. Turn off the gas supply ball valve to the unit and then complete the following steps:

a) Use jumper wires to jump out the Low Gas Pressure switch and Blower Proof switch.

b) Remove the black connector boot from the Flame Detector.

Create a connector as shown below and connect it to the Flame Detector’s black
connector boot. Keep the alligator clip away from bare metal parts until step 5b.

Figure 6-9: Connecting the Flame Signal Generator

4. Go to

Diagnostics

→

Manual Run

and enable the

Manual Mode

control.

5. Complete the following:

Ramp the Water Heater up to 100% fire rate and then set the Controller’s

Enable/Disable

switch to

Enable

b) When the Controller gets into the ignition phase, it will show

Ignition Trial

. At that

point attach the alligator clip (see Figure 6.8-3) to any bare metal surface or
ground. The Controller displays

Flame Proven

and begins to ramp up to 100% fire

rate. Note that no gas or flame is present in the Water Heater at this time.

6. Wait for the unit to ramp up to at least 90% before continuing.

7. Cover the combustion air inlet opening with a solid, flat object, such as a piece of thick

plywood or a thick metal plate.

8. The unit should shut down and display

Airflow Fault During Run

. This step confirms

proper operation of the Blocked Inlet switch.

9. Remove cover from air inlet opening and reinstall the Combustion Air Duct or air filter.

10. Remove jumper wires installed in step 3 and replace the black connector boot on the

Flame Detector.

11. Press the

CLEAR

button. The unit should restart.

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands