Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 71

Page: 71 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 7: MAINTENANCE

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 71 of 131

7.8 AIR FILTER CLEANING AND REPLACEMENT

The Water Heater

’s air filter should be maintained as follows:

Cleaned:

every 12 months.

Replaced:

after 24 months if it shows any signs of deterioration. However, if still in good

condition you can order a 24 Month Maintenance kit with air filter cleaning kit.

NOTE:

Failure to clean or replace the air filter may affect stable combustion, result in less

efficient operation, and may result in combustion reliability issues.

All 24 Month Maintenance Kits include one of two parts:

•

An Air Filter Cleaning Kit

– Appropriate if the filter is intact

•

New Air Filter

– Necessary if the filter is deteriorated or damaged

Check the table below to find the part number of the kit appropriate for your site. Instructions are
included in the TID that accompanies the kit.

Maintenance Kits Numbers

12 Month Maintenance Kit: 58025-25
24 Month Maintenance Kit w/ air filter replacement: 58025-26
24 Month Maintenance Kit w/ air filter

cleaner

: 58025-27

Figure 7-7: Air Filter Location

AIR FILTER

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands