Watts CEN2000 Installation, Operation And Maintenance Manual Download Page 63

Page: 63 / 131

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 6: SAFETY DEVICE TESTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 63 of 131

6.9 SSOV PROOF OF CLOSURE SWITCH CHECK

The SSOV (shown in Figure 6-7) contains the

Proof of Closure

switch. The

Proof of Closure

switch circuit is checked as follows:

Set the Controller’s

Enable/Disable

switch to

Disable

2. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

3. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

4. Loosen the SSOV cover screw and remove cover to access wiring connections.

5. Disconnect wire #1304

from the SSOV to “open” the Proof of Closure switch circuit.

6. The unit should fault and display

SSOV Switch Open

7. Replace wire #1304 and press the

CLEAR

button.

Set the Controller’s

Enable/Disable

switch to

Enable

to start the unit.

9. Remove the wire again when the unit reaches the purge cycle and

Purging

is displayed.

10. The unit should shut down and display

SSOV Fault During Purge

11. Replace the wire on the SSOV and press the

CLEAR

button. The unit should restart.

6.10 PURGE SWITCH OPEN DURING PURGE

The

Purge

switch (and

Ignition

switch) is located on the Air/Fuel Valve. To check the switch:

Set the Controller’s

Enable/Disable

switch to

Disable

2. Go to

Main Menu

→

Diagnostics

→

Manual Run

and enable

Manual Mode

3. Set the valve position

between 25% and 30%

using the

(Plus) and

–

(Minus) controls.

4. Remove the Air/Fuel Valve cover by rotating the cover counterclockwise to unlock it.

5. Remove one of the two wires (#1609 or #1610) from the Purge switch (Figure 6-11).

Set the Controller’s

Enable/Disable

switch to

Enable

to start the unit.

7. The unit should begin its start sequence, then shut down and display

Prg Switch Open

During Purge

Figure 6-10: Air/Fuel Valve Cover Location

Summary of Contents for CEN2000




































































































































Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands

Watts CEN2000, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for CEN2000

Reviews:

Related manuals for CEN2000

Brands by name

Popular brands