Stand-up paddleboard – Instructions for use
|
3
UK
INSTRUCTION
These operating instructions should be
read and followed up carefully before utilizing the
SUP board. When passing the product on to a third
party, always make sure that the documentation is
included. Take special care to follow up the correct
sequence of inflating/deflating of the assembling
procedure.
CONTENTS
1 Inflatable Stand-Up paddleboard
1 Backpack
1 Aluminium adjustable paddle
1 Hand Pump
1 Leash.
1 Detachable skeg
1 Repair kit
1
1. H3 Valve
2. Front bungee cord
3. Non slip EVA pad
4. Carry handle
5. Metal ring
6. Detachable skeg
WARNING
- SUP can be very dangerous and physically
demanding. The user of this product should
understand that participating in stand up paddling
may involve serious injury or death.
- Seek SUP instruction from a licensed or certified
instructor.
- Always check weather forecasts prior to using
the SUP board. Never use the SUP board in
thunderstorms and lighting conditions.
- Always use appropriate protective gear and wear
a personal flotation device. Wear the correct
protective clothing for the conditions such
as a wetsuit or a UV top. Cold water and cold
weather can result in hypothermia. Always carry
identification.
- Wear a helmet when appropriate.
- Do not exceed the maximum weight capacity of
100 kg.
- Do not operate the SUP board under the influence
of drugs and/or alcohol.
- This model is designed to be used in flat waters
(lake, rivers, sea shore) in standing and seating
position. It is not recommended to use the SUP
board in high waves nor for surfing.
- Beware of offshore winds and currents as they can
take you out to sea.
- Check your equipment prior to each use for signs of
wear, leaks or failure.
- Protect this article from extreme temperatures,
sun and humidity.
- Tie the included leash to your SUP board at all times.
- Children should always be under adult supervision.
- Always inform someone your paddling route, the
time and place of departure and your intended
time and place of arrival. Paddling alone is not
recommended.
- Watch out for other beach users especially
swimmers and children. Make sure you keep the
SUP board and paddle under control at all times.
- Never leave your SUP board for an extended period
of time on a warm surface like a beach or other
surfaces. This can cause damage to your board.
- Dispose of the item in accordance with local,
current regulations at a collection point.
PREPARATIONS FOR INFLATING THE SUP
BOARD
Remove all sharp edged and pointed objects from the
surface in order to avoid damaging the SUP board.
ASSEMBLY INSTRUCTIONS / INFLATION / DEFLATION
Inflate the SUP board with the included hand pump.
2
1. Valve cap
2. Button
3. Valve base
- Unscrew the valve cap
1
. Push the button
2
in
and turn approximately 90 degrees so it is in the
“OUT” position.
- Insert the pump hose end piece and inflate it until
you will reach the required pressure. After inflation
tighten all the valve cap (clockwise). Only the valve
cap can ensure final AIR TIGHTNESS.
- To release air from the SUP board, remove the
valve cap
1
and push the button
2
in and turn
approximately 90 degrees so it is in the “IN” position.
The correct pressure for this SUP board is
maximum 1 bar / 15 PSI (=1000 mBar)
DO NOT EXCEED THIS !!
Using an electrical pump or air compressor is at your
own risk. This can lead to damaging the SUP board.
Lock pin
DETACHABLE SKEG ON BACKSIDE OF SUP BOARD
It is recommended to use the detachable skeg in deep
water, where it will allow you to move forward in a
straight line. Do not use it in shallow water because
then the skeg can hit the bottom. The Skeg can be
placed on the SUP board if this is inflated or deflated.
To assemble the skeg push the skeg in the black part
on the back side of the SUP board. To lock the skeg
push the lock pin in the skeg base hole.
4
ASSEMBLY INSTRUCTIONS INCLUDED PADDLE
The included paddle consists of 3 pieces.
To adjust the paddle to the required length:
- Insert the bottom of pole
2
in to the top of pole
3
.
This can be fixed when the pin on pole
2
is clicked
in the hole of pole
3
.
- Open the button on top of pole
2
by pulling the button.
- Insert the bottom of pole
1
and choose the length
that suits you. Click the pin (behind the button) of
pole
2
in to the hole of pole
1
.
- The paddle length is adjustable from minimum
length 1.70 mtr to maximum length 2.10 mtr.
HOW TO USE YOUR PADDLE
Don’t use the peddle as support to stand on the
SUP. The peddle is only allowed to be used for
peddling in the water and can break when it comes
in contact with the lake/sea-bed.
ATTACHING THE LEASH
Before you start to use the SUP board first attach
included leash to the SUP board and yourself.
- Attach the leash to the metal ring on top of the
SUP board.
- Attach the other side of the lease to your ankle.
When you fall in the water the leash ensures that
the SUP board will not float away.
MAINTENANCE SUP BOARD
- Clean and check the SUP board and all accessories.
Use a mild, non scouring cleanser.
- Make sure the SUP board is completely dry before
placing it in the backpack. Otherwise this may cause
mold, foul odor and the skin/hull or the inside chambers
of the SUP board will suffer from water damage.
REPAIRS
Although the SUP board has been manufactured of
a reinforced and tough material, it is still possible to
cause holes or cracks when the SUP board is handled
improperly. For the repair of a small damage a repair
kit is included.
- Prepare a round patch with repair material with
correct measurements.
- Clean the repair material and the area around the
leak with alcohol.
- Apply 3 thin, even coats of glue to both the surface
of the board and the repair material. Wait 5
minutes between each coat.
- After the 3rd coat, wait 10-15 minutes before
applying the repair material. Use a handroller
to apply the repair material evenly. Pay special
attention to the edges.
- Wait at least 24 hours before re-inflating.
- Many tutorials on social media regarding SUP
repairs.
3