Volkswagen CJDA Workshop Manual Download Page 154 | Manualshive

Page: 154 / 553

background image

13 - Crankshaft group

1

Dismantling and assembling en-

gine

WARNING

Adhere to the general safety regulations and the notes on
repair work on the engine!

WARNING

When doing any repair work, pay attention to the follow-
ing due to the cramped conditions:

◆

Adhere to the general safety precautions, and never
take any risk.

◆

The engine is a hazardous area and can cause seri-
ous injuries.

◆

Never leave any objects in the engine compartment,
such as cleaning cloths or tools.

◆

Many engine components become hot during opera-
tion – risk of burns. If necessary, provide appropriate
protective means.

◆

Servicing materials, such as fuel, engine oils or cool-
ant additive, are harmful substances; adhere to the
safety instructions from the manufacturer.

◆

There is a risk of injuries, if maintenance locations
are difficult to access. This risk can be reduced, by in-
stalling the engine in an appropriate location and by
avoiding sharp edges.

◆

Route all the various lines (e.g. for fuel, hydraulics,
coolant and refrigerant, brake fluid and vacuum) and
electrical wiring in their original positions.

◆

Ensure that there is sufficient clearance to all moving
or hot components.

◆

Tools are to be checked for damage and safety risks
on a regular basis.

Note

◆

Before carrying out repair work, secure engine on engine
and gearbox support -VAS 6095- using universal mounting
-VAS 6095/1-.

◆

All bearing and running surfaces must be oiled before as-
sembly.

3

Industriemotoren - Industrial Engines 2009

▶

Workshop Manual for Diesel Engine (2.0 l/36-75 kW_EA 189) 05.2015

138

Repair Group 13 - Crankshaft group

«
...
152
153
154
155
156
...
»

Summary of Contents for CJDA










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CJDA

Brand: BAFANG Pages: 12

Electric Motor G2909

Brand: Grizzly Pages: 2

Brand: Nanni Pages: 32

Brand: TOHATSU Pages: 292

Command Pro EFI ECH940

Brand: Kohler Pages: 8

Courage PRO SV810

Brand: Kohler Pages: 20

KDI 3404TCR-SCR

Brand: Kohler Pages: 64

Brand: Kohler Pages: 88

Brand: Kohler Pages: 334

Brand: Lombardini Pages: 12

Brand: Lombardini Pages: 44

Brand: Lombardini Pages: 54

Brand: Volvo Pages: 8

Brand: GPOWER Pages: 4

Brand: Robin America Pages: 31

Brand: Hino Motors Pages: 236

Brand: Stober Pages: 34

Brand: Baumuller Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands