VESPA LX Series User Manual Download

Page: 147 / 272

OMPONENT

RANSPOSITION

Specification

Desc./Quantity

Instrument panel

Throttle body and electronic injection control unit (MIU)

Diagnostics socket connector

Fuel pump

Engine temperature sensor

Fuel injector

HV coil

Engine speed sensor

Lambda probe

Injection load remote control

Battery

12V10Ah

MIU injection system

This vehicle is fitted with an integrated injection and ignition system.

Injection is indirect in the manifold through an electro-injector.

The injection and ignition are timed on the four-stroke cycle by means of a tone wheel keyed on to the

crankshaft (24-2 teeth) and pick-up sensor.

Vespa LX 125 - 150 i.e.

Injection

INJEC - 147

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands