VESPA LX Series User Manual Download

Page: 120 / 272

020427Y

Piston assembly band

Inspecting the cylinder head

- Using a trued bar check that the cylinder head

surface is not worn or distorted.

- Check that the camshaft and rocking lever pin

bearings show no signs of wear.

- Check that the cylinder head cover surface, the

intake manifold and the exhaust manifold are not

worn.

Characteristic

Maximum admitted unevenness: Head check

0.05 mm

STANDARD DIAMETER

Specification

Desc./Quantity

Standard diameter

A Ø 32.5 to 32.525

Standard diameter

B Ø 20 to 20.021

Standard diameter

C Ø 12 to 12.018

Inspecting the timing system components

- Check that the guide slider and the tensioner

slider are not worn out.

- Ensure that the camshaft drive pulley, the chain

assembly and the sprocket wheel are not worn.

- If sings of wear are found, replace the parts. if the

chain, pinion or pulley are worn, replace the whole

assembly.

Engine

Vespa LX 125 - 150 i.e.

ENG - 120

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands