VESPA LX Series User Manual Download

Page: 111 / 272

Removing the starter motor

- Remove the two screws indicated in the figure.

- Take the starter motor out of its seat.

Removing the flywheel magneto

- Lock the rotation of the flywheel using the calliper

spanner.

- Remove the nut.

CAUTION

THE USE OF A CALLIPER SPANNER OTHER THAN THE
ONE SUPPLIED COULD DAMAGE THE STATOR COILS

Specific tooling

020565Y

Flywheel lock calliper spanner

- Extract the flywheel with the extractor.

Specific tooling

008564Y

Flywheel extractor

Inspecting the flywheel components

- Check the integrity of the internal plastic parts of the flywheel and the Pick-up control plate.

Vespa LX 125 - 150 i.e.

Engine

ENG - 111

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands