VESPA LX Series Page 110 User Manual Download

Page: 110 / 272

Removing the stator

- Remove the magneto flywheel.

- Remove the electric terminal of the minimum oil

pressure switch.

- Remove the two Pick-Up screws and the one for

the wiring harness bracket as well as the two stator

fixing screws shown in the figure.

- Remove the stator and its wiring.

Refitting the stator

- Refit the stator and flywheel carrying out the re-

moval procedure in reverse, tightening the retain-

ers to the specified torque.

- Place the cable harness as shown in the figure.

N.B.

THE PICK-UP WIRE SHOULD BE POSITIONED BETWEEN
THE UPPER SCREW AND THE REFERENCE PIN AS
SHOWN IN THE DETAIL DRAWING.

Locking torques (N*m)

Stator screw

3 to 4

Flywheel and starting

Engine

Vespa LX 125 - 150 i.e.

ENG - 110

Summary of Contents for LX Series

















































































































































































































































































Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands

VESPA LX Series, User Manual

Search results

Summary of Contents for LX Series

Reviews:

Related manuals for LX Series

Brands by name

Popular brands